Influencia de la proporción de fibra de yute:fibra de vidrio y tratamiento superficial sobre la resistencia a la tracción de un material compuesto de matriz poliéster fabricado mediante el método de compresión
No Thumbnail Available
Date
2018-09
Journal Title
Journal ISSN
Volume Title
Publisher
Universidad Nacional de Trujillo
Abstract
En la presente investigación se evaluó la Influencia de la proporción de fibra de
yute:fibra de vidrio y tratamiento superficial sobre la resistencia a la tracción de un
material compuesto de matriz poliéster, fabricado mediante el método de compresión.
La proporción de fibra de yute:fibra de vidrio utilizados en la evaluación fueron de 1:1;
2:1; 3:1; 4:1; además las fibras naturales se trabajaron en fibras largas, para las fibras
sintéticas (fibra de vidrio) se utilizaron tejidas bidireccionalmente; y se analizó la
influencia que tienen cuando las fibras naturales son sometidas a un tratamiento
superficial de mercerización, el cual fue trabajado a dos porcentajes de NaOH, al 5% y
10%. Todas la probetas fueron fabricadas mediante el método de compresión, y
conformadas en placas de 30 cm x 20 cm con un espesor de 0.5 cm; posteriormente
sometidas a un curado de 72 horas. Se evaluó la resistencia a la tracción según la normal
ASTM D-628-01.
De los resultados obtenidos, se determinó que los valores de resistencia a la tracción
obtenidos son mayores en comparación con el material compuesto, resina y fibra de
yute; donde este compuesto presenta un valor promedio de 47.17 MPa; y nuestras
probetas sin ser sometidas a tratamiento superficial, presentan una resistencia a la
tracción mínima de 55.47 MPa para la proporción 1:1; fibra de yute:fibra de vidrio; y
máxima de 82.38 MPa para la proporción de 3:1.
De igual forma; los valores de resistencia a la tracción obtenidos son mayores en
comparación con el material compuesto, resina y fibra de yute; sometidos a tratamiento
superficial al 5% y 10% de NaOH; donde este compuesto presenta un valor promedio
de 56.27 MPa y 60.60 MPa, respectivamente; y nuestras probetas sometidas a
tratamiento superficial al 5% y 10% de NaOH, presentan una resistencia a la tracción
mínima de 64.15MPa y 67.49MPa, respectivamente; para la proporción 1:1; fibra de
yute:fibra de vidrio; y máxima de 85.55 MPa y 92.22 MPa, respectivamente; en la
proporción de 3:1.
Los resultados son confirmados mediante análisis de varianza para un nivel de
confianza de 95% donde concluye que la resistencia a la tracción más alta es dada a
proporciones 3:1, en fibra de yute:fibra de vidrio, y con fibras mercerizadas a un 10%
de NaOH.
Description
In the present investigation, the influence of the proportion of jute fiber: glass fiber and
surface treatment on the tensile strength of a polyester matrix composite material,
manufactured by the compression method, was evaluated.
The proportion of jute fiber: fiberglass used in the evaluation were 1: 1; 2: 1; 3: 1; 4: 1;
In addition, natural fibers were worked on long fibers, for synthetic fibers (fiberglass)
they were woven bidirectionally; and analyzed the influence they have when the natural
fibers are subjected to a surface treatment of mercerization, which was worked at two
percentages of NaOH, 5% and 10%. All the specimens were manufactured by the
compression method, and formed into 30 cm x 20 cm plates with a thickness of 0.5 cm;
subsequently subjected to a cure of 72 hours. The tensile strength was evaluated
according to the normal ASTM D-628-01.
From the results obtained, it was determined that the tensile strength values obtained are
greater in comparison with the composite material, resin and jute fiber; where this
compound has an average value of 47.17 MPa; and our test pieces without being
subjected to surface treatment, have a minimum tensile strength of 55.47 MPa for the
ratio 1: 1; Jute fiber: fiberglass; and maximum of 82.38 MPa for the 3: 1 ratio.
Similarly; the tensile strength values obtained are greater in comparison with the
composite material, resin and jute fiber; subjected to surface treatment at 5% and 10%
NaOH; where this compound presents an average value of 56.27 MPa and 60.60 MPa,
respectively; and our test pieces subjected to surface treatment at 5% and 10% NaOH,
have a minimum tensile strength of 64.15MPa and 67.49MPa, respectively; for the 1: 1
ratio; Jute fiber: fiberglass; and maximum of 85.55 MPa and 92.22 MPa, respectively;
in the ratio of 3: 1.
The results are confirmed by analysis of variance for a confidence level of 95% where it
concludes that the highest tensile strength is given at 3: 1 proportions, in jute fiber: glass
fiber, and with mercerized fibers at 10 % NaOH.
Keywords
Matriz poliéster