Influencia del tiempo de recocido sobre la dureza y resistencia al impacto de una fundición gris perlítica en la obtención de una fundición gris ferrítica
No Thumbnail Available
Date
2017-01-31
Journal Title
Journal ISSN
Volume Title
Publisher
Universidad Nacional de Trujillo
Abstract
En ésta investigación se estudió la influencia del tiempo de recocido sobre la dureza
y resistencia al impacto de una fundición gris perlítica en la obtención de una fundición
gris ferrítica. Por lo cual se empleó barras cuadradas de 12 mm x 12 mm x 200 mm de
longitud suministrado por fundición metalúrgica y servicio afines (FUMETSA), las cuales
fueron recocidas a 860°C a los tiempos de 0.5, 1, 2, 5, 10, 15 y 20 horas con enfriamiento
lento dentro del horno. Las probetas fueron maquinadas para el ensayo de dureza según
norma ASTM E-140 y resistencia al impacto según norma ASTM E23-98.
Los resultados experimentales muestran que al incrementar el tiempo de recocido
la dureza disminuye desde 213. 10 HB para suministro (0 horas) a 108.10 HB para 20
horas de tratamiento y la resistencia al impacto aumenta desde 9.40 J para suministro
hasta 23.60 J para 20 horas. Esto es debido a la descomposición de la austenita en ferrita
grafito en forma de hojuelas haciendo que el material sea blando y tenaz. También
mostró que los valores obtenidos de resistencia al impacto (J) para todos los niveles de
tiempo de recocido son bajos debido a las hojuelas de grafito que se engruesan con el
incremento del tiempo de recocido.
También se observa que el tiempo de descomposición total de la austenita en ferrita
para la obtención de fundición gris ferrítica para esta fundición en las condiciones de
estudio fue de 2 horas.
Se concluye que el tiempo de maleabilización influye significativamente la dureza y
resistencia al impacto según el análisis estadístico con un 95% de confiabilidad.
Description
In this research the influence of the annealing time on the hardness and impact
resistance of a gray pearl smelter in the production of a ferritic gray smelter was studied.
For that reason, square bars of 12 mm x 12 mm x 200 mm in length supplied by
metallurgy and related services (FUMETSA) were used, which were annealed at 860 ° C
at the times of 0.5, 1, 2, 5, 10 , 15 and 20 hours with slow cooling inside the oven. The
test pieces were machined for the hardness test according to ASTM E-140 and impact
strength according to ASTM E23-98.
The experimental results show that by increasing the annealing time the hardness
decreases from 213. 10 HB for supply (0 hours) to 108.10 HB for 20 hours of treatment
and the impact resistance increases from 9.40 J for delivery up to 23.60 J for 20 hours .
This is due to the decomposition of the austenite in graphite ferrite in the form of flakes
making the material soft and tenacious.
It also showed that the obtained values of impact resistance (J) for all annealing
time levels are low due to the graphite flakes that increase with the increase of
annealing time.
It is also observed that the total decomposition time of the austenite in ferrite to
obtain ferritic gray smelter for this melt in the study conditions was 2 hours.
It is concluded that the malleability time significantly influences the hardness and
impact resistance according to the statistical analysis with 95% reliability.
Keywords
Fundición gris, recocido, perlita, ferrita, dureza, resistencia al impacto